Tascam CD Player CD 01 U User Manual

D00864010A  
»
CD-01U/CD-01UPro  
CD PLAYER  
OWNER’S MANUAL  
˛
 
Important Safety Instructions  
1 Read these instructions.  
2 Keep these instructions.  
3 Heed all warnings.  
• Do not expose this apparatus to drips or splashes.  
• Do not place any objects filled with liquids, such as  
vases, on the apparatus.  
• Do not install this apparatus in a confined space such as  
a book case or similar unit.  
4 Follow all instructions.  
5 Do not use this apparatus near water.  
6 Clean only with dry cloth.  
• The apparatus draws nominal non-operating power from  
the AC outlet with its POWER switch in the off position.  
• The apparatus should be located close enough to the AC  
outlet so that you can easily grasp the power cord plug at  
any time.  
7 Do not block any ventilation openings. Install in accor-  
dance with the manufacturer's instructions.  
8 Do not install near any heat sources such as radiators,  
heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
• An apparatus with Class I construction shall be connect-  
ed to an AC outlet with a protective grounding connec-  
tion.  
9 Do not defeat the safety purpose of the polarized or  
grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety. If  
the provided plug does not fit into your outlet, consult  
an electrician for replacement of the obsolete outlet.  
10 Protect the power cord from being walked on or  
pinched particularly at plugs, convenience receptacles,  
and the point where they exit from the apparatus.  
11 Only use attachments/accessories specified by the  
manufacturer.  
12 Use only with the cart, stand, tripod, bracket, or table  
specified by the manufacturer, or sold with the appara-  
tus. When a cart is used, use caution when moving the  
cart/apparatus combination to avoid injury from tip-  
over.  
13 Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
14 Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or  
plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has been  
exposed to rain or moisture, does not operate normally,  
or has been dropped.  
TASCAM CD-01U/CD-01UPro  
 
3
Safety Information  
This product has been designed and manufactured  
according to FDA regulations "title 21, CFR, chapter  
1, subchapter J, based on the Radiation Control for  
Health and Safety Act of 1968", and is classified as a  
class 1 laser product. There is no hazardous invisible  
laser radiation during operation because invisible  
laser radiation emitted inside of this product is com-  
pletely confined in the protective housings.  
The label required in this regulation is shown 1.  
CAUTION  
• DO NOT REMOVE THE PROTECTIVE HOUSING  
USING A SCREWDRIVER.  
• USE OF CONTROLS OR ADJUSTMENTS OR PER-  
FORMANCE OF PROCEDURES OTHER THAN  
THOSE SPECIFIED HEREIN MAY RESULT IN HAZ-  
ARDOUS RADIATION EXPOSURE.  
• IF THIS PRODUCT DEVELOPS TROUBLE, CON-  
TACT YOUR NEAREST QUALIFIED SERVICE PER-  
SONNEL, AND DO NOT USE THE PRODUCT IN  
ITS DAMAGED STATE.  
Optical pickup:  
Type:  
KSM-900AAA  
Manufacturer: SONY Corporation  
Laser output: Less than 0.5 mW on the objec-  
tive lens  
Wavelength: 775 to 815 nm  
4
TASCAM CD-01U/CD-01UPro  
 
Table of contents  
1 - Introduction  
7 - Advanced operations  
Auto Cue ......................................................18  
Auto Ready .................................................18  
Resume .........................................................18  
Call ....................................................................18  
Incremental play ..................................................19  
Repeat playback .........................................19  
A to B repeat playback ...............................19  
Intro check .......................................................20  
Output in monaural ..............................................20  
Power on play ................................................20  
Pitch control ..................................................20  
Changing the playback speed without changing  
the key (Key original) ...................21  
Supplied accessories ..................................6  
Environmental considerations .....................6  
Some notes and precautions ..........................6  
Beware of condensation .....................6  
Back up memory .................................6  
Rack - mounting the unit .......................7  
Handling of compact discs ...........................7  
2 - Remote control unit  
Some notes and precautions .......................8  
Batteries ........................................................8  
Inserting batteries .....................................8  
3 - Connections  
Program playback .......................................21  
Editing a programmed track ......................21  
Adding a track to the program .................21  
Deleting a programmed track ....................22  
Fade in and fade out .......................................22  
Relay play ................................................22  
Time display switching ..............................23  
End of disc/track warning ......................................23  
Eject block .............................................23  
Fader start/Event start ..............................23  
Fader start/stop .....................................23  
Event start ...........................................24  
Restoring factory default settings ...................24  
External parallel control ........................................24  
Audio equipment .......................................9  
Connecting analog audio equipment ...........9  
Connecting digital audio equipment ..........9  
Power source ................................................9  
4 - Features and their functions  
Front panel ..................................................10  
Display .......................................................11  
Rear Panel ...................................................12  
Remote Control Unit ..................................12  
5 - Menu operation  
Menu configuration ...................................14  
Menu operation .........................................14  
Operation basics .........................................14  
8 - Specifications  
Specifications ........................................................25  
Dimensional drawing ................................26  
Error Messages ...........................................26  
6 - Playback  
Discs for playback .......................................15  
About finalization .......................................15  
For MP3 CDs ............................................15  
Playback modes ..........................................16  
Basic playback operation ...........................16  
Using headphones .......................................16  
Track selection ............................................16  
Selecting by track number .......................17  
Search ..........................................................17  
Frame search ...................................17  
TASCAM CD-01U/CD-01UPro  
5
 
Œ
1 - Introduction Environmental considerations  
Thank you for your purchase of the TASCAM CD-  
01U/CD-01U Pro CD player.  
CD-01U/CD-01U Pro, as well as the operation of its  
many useful and convenient functions. After you have  
finished reading this manual, please keep it in a safe  
place for future reference.  
Before connecting and using the unit, please take time  
to read this manual thoroughly to ensure you under-  
stand how to properly set up and connect the  
Supplied accessories  
In addition to this manual, the CD-01U/CD-01U Pro  
have been packed with the following:  
Should any of these items be missing, or if you  
encounter any damage, please contact your TASCAM  
supplier.  
RC-01UC remote control unit  
2 AAA batteries  
Power cord  
Rack-mounting kit  
Warranty document  
This unit was packed in its carton with special materials  
in order to prevent any damage during shipment.  
Please save the carton and packing materials in the  
event you need to transport the unit in the future.  
Environmental considerations  
The CD-01U/CD-01U Pro may be used in most places,  
but to maintain top performance and prolong operating  
life, do not place it in the following locations.  
Near heating or air conditioning vents, or in very hot or  
cold places  
Places with high humidity or poor ventilation  
Next to tuners, televisions or video decks, as this  
On an unsteady surface, or where there is frequent  
could cause noise or affect video images  
vibration or resonance  
Near a window or where it can be exposed to direct  
sunlight  
Some notes and precautions  
Connect the CD-01U/CD-01U Pro only to the specified  
power source.  
Clean only with a dry cloth. Do not use benzene, paint  
thinner or other agents that could damage the surface.  
Dust or grime on the top cover can be removed with a  
soft cloth lightly moistened with a diluted mild detergent  
solution.  
When unplugging the cord, grasp the plug itself.  
Beware of condensation  
If the unit is moved from a cold to a warm place, or  
used after a sudden temperature change, condensation  
inside the unit may occur, resulting in moisture on the  
internal mechanism or an inserted disc, thus impairing  
proper operation.  
Should this occur, leave the player turned on for one or  
two hours so that the condensation can evaporate  
before you begin operation.  
Also, please remove all discs from the unit if it will be  
moved, or not operated for an extended period of time.  
Backup Memory  
Even when the power is turned off, the following set-  
tings are retained.  
Playback mode  
Time display mode  
Auto ready ON/OFF  
Auto cue ON/OFF  
Pitch control value  
All menu settings  
6
TASCAM CD-01U/CD-01UPro  
 
Œ
1 - Introduction Environmental considerations  
Rack-mounting the unit  
Use the rack-mounting kit to mount the unit in a  
standard 19-inch equipment rack, as shown below.  
Remove the feet of the unit before mounting.  
If you are mounting the unit in a rack, leave 1U of  
space above it and 10cm (4 in) or more of space at  
the rear. The CD-01U/CD-01U Pro can be mounted  
in any angle between 0 to 90 degrees.  
SeeEnvironmental considerationson the previous page.  
Handling of compact discs  
The CD-01U/CD-01U Pro have been designed for the  
Keep discs away from direct sunlight, and places of  
high heat and humidity. If left in such places, warping  
playback of CD-DA format discs and MP3 files record-  
ed in ISO9660 format. In addition to ordinary 5-inch and  
3-inch CDs, it can also play properly recorded CD-R  
and CD-RW discs.  
could result.  
Do not affix any labels or stickers to the label side of  
the disc. Do not write on the disc with a ballpoint  
pen.  
When removing a CD from its case, press down on the  
center of the disc holder to free the CD, then lift the disc  
out, holding it carefully by the edges.  
Please do not insert discs that have adhesive remain-  
ing from tape or stickers that have been removed. If  
they are inserted into the player, they could stick to  
the internal mechanism, requiring removal by a tech-  
nician.  
Removing a disc  
Hold the CD like this  
Only use circular compact discs. Avoid using non-cir  
cular promotional, etc. discs.  
The CD-01U/CD-01U Pro cannot play unfinalized  
CD-R/RW discs.  
Do not use a C-thru disc.  
Avoid getting fingerprints on the signal side (opposite  
the label side). When cleaning, wipe gently with a soft  
cloth from the center towards the outside edge. Dust  
and grime may cause skipping, so keep discs clean  
and store them in their cases when not being played.  
The unit does not support a C-thru disc. Therefore,  
you may not be able to insert a C-thru disc or may  
not be able to remove a C-thru disc that has been  
successfully inserted to the unit.  
In the latter case, try to press the DISPLAY and  
EJECT keys simultaneously, which may solve the  
problem.  
Do not use the DualDisc. DualDisc is two-sided play-  
back only discs. Insertion or ejection of a DualDisc  
into/from CD-01U/CD-01U Pro is likely to cause  
scratches to the surface of the DualDisc. Scratched  
discs may not play in CD products.  
Do not use any record spray, anti-static solutions,  
benzene, paint thinner or other chemical agents to  
clean CDs as they could damage the delicate playing  
surface.  
A DualDisc may not play in CD-01U/CD-01U Pro and  
a DualDisc could get stuck in and may not be able to  
be removed from the CD-01U/CD-01U Pro.  
Discs should be returned to their cases after use to  
avoid serious scratches that could cause the laser  
pickup to skip.  
TASCAM CD-01U/CD-01UPro  
7
 
2 - Remote control unit  
Some notes and precautions  
Batteries  
When the remote control will not be used for an  
extended period of time, please remove the batteries  
to prevent the possibility of battery acid leakage  
which could damage the unit.  
If batteries are used improperly, or if leakage or break-  
age occurs, the unit will not function.  
Please observe the cautions indicated on the batteries  
and their packaging to ensure proper usage.  
Should leakage occur, remove and discard the bat-  
teries, and wipe the battery case thoroughly with a  
cloth.  
Confirm + and - polarity and follow the indications  
when inserting new batteries into the remote control.  
Avoid getting the battery liquid on the skin. After  
cleaning, replace with new batteries.  
Do not use old and new batteries together.  
Even if the battery is the same size, the voltage may  
The remote control functions by using an infrared  
light signal. When using the unit to control the CD-  
01U/CD-01U Pro, other devices that are turned on  
could be operated by its signal.  
differ.  
Do not use batteries of different specifications  
together.  
Do not attempt to recharge batteries that are non-  
If the range of remote operation becomes smaller, or  
commands do not always function properly, the bat-  
teries have become weak and should be replaced.  
Always replace both batteries with new batteries of  
the same type.  
rechargeable.  
Do not open or disassemble batteries, throw them  
into a fire or put them in water.  
Inserting batteries  
Point the remote control to the remote sensor on the  
main unit.  
1. Open the lid.  
Do not obstruct the path between the remote control  
and the remote sensor.  
2. Confirm +/- polarity, and insert two AAA batteries.  
3. Close the lid.  
7 m  
8
TASCAM CD-01U/CD-01UPro  
 
3 - Connections  
Before connecting the CD-01U/CD-01U Pro to other units, please read their operation manuals thoroughly to ensure  
proper connection. Turn the power on only after all connections have been made.  
Audio equipment  
Connecting analog audio equipment  
Connecting digital audio equipment  
Connect analog stereo amplifiers, mixers and recorders  
to the analog line outputs.  
Digital stereo amplifiers, mixers and recorders can be  
connected through the optical digital output terminal.  
Power source  
Connection cables are not supplied with this unit.  
Do not bundle the pin connection cords with the  
power cord as noise or diminished sound quality  
could result.  
This unit has been designed to operate on the specified  
power voltage only.  
Do not plug the power cord into outlets of any other  
voltage.  
TASCAM CD-01U/CD-01UPro  
9
 
4 - Features and their functions  
Front panel  
1 POWER switch  
0 DISPLY key  
2 Disc slot  
Pressing this key changes the time mode on the dis-  
play. Even when the power is turned off, the time  
mode is retained.  
Insert CD into the slot, label side upwards.  
3 Remote signal sensor  
4 EJECT key  
When in menu mode, exits the menu mode.  
q SHIFT key and indicator  
Ejects a disc. This key cannot be used when Eject  
Block is on and disc is being played back.  
Turns the shift mode on and off. When in shift mode,  
the indicator lights and other keys have shift func-  
tions which indicated under the keys.  
5 Display  
The display is used to show the current status of the  
unit, as well as the current menu settings.  
Pressing this key again exits shift mode.  
w ¥?π (JOG) key and indicator  
6 PITCH (MENU) control knob  
Changes the playback mode between playback and  
pause.  
Push this control to turn the pitch control function on  
or off. When it is on, pitch value is shown on the  
Display, and pitch can be controlled +/- 12.5%.  
Even when the power is turned off, the pitch control  
ON/OFF setting is retained.  
The indicator stays on solid in playback mode and  
flashes in pause mode.  
When playback is paused and SHIFT indicator is lit,  
frame accurate search can be performed using with  
the PITCH knob.  
When in shift mode, functions as the menu dial when  
rotated, and as the ENTER key when pushed.  
e CALL (PLAY MODE) key  
When playback is paused and SHIFT indicator is lit,  
frame accurate search can be performed using with  
this knob.  
Locates the playback to the last play start point.  
When SHIFT indicator is lit, selects the playback  
7 SKIP (INDEX/DIR SEARCH) keys  
mode.  
Use these to perform track searches.  
r ª (INTRO CHECK) key  
When SHIFT indicator is lit, searches the index  
Use this key to stop playback.  
(Audio CD discs) or directory (MP3 discs).  
When Incremental Play is activated, pressing this key  
pauses at the beginning of next track.  
8 SEARCH (A.CUE, A.RDY) keys  
Performs review or cue playback (search).  
When in shift mode, enters Intro Check mode.  
When in shift mode, selects the Auto Cue level or  
turns the Auto Ready mode on and off.  
t PHONES jack  
Use a standard pair of stereo headphones, equipped  
with a 1/4-inch plug, with this jack.  
9 PHONES level control  
Adjusts the headphone output level.  
10  
TASCAM CD-01U/CD-01UPro  
 
4 - Features and their functions  
Display  
1TRACK indicator  
8 REPEAT indicators  
2 Track number display  
Indicates the current repeat mode.  
Shows the track number. In the menu mode, shows  
the menu number.  
9 PITCH indicator and pitch value display  
When pitch control is activated, shows the pitch  
3 MP3 indicator  
value and PITCH indicator lights.  
Lights when a MP3 CD-ROM disc is inserted.  
4 INDEX/DIR indicator  
In the menu mode, shows the menu parameters.  
0 A.CUE indicator  
Shows the index number (CD-DA) or directory  
number (MP3).  
Lights when Auto Cue function is turned on.  
q A.RDY indicator  
5 T and REMAIN indicators  
Lights when Auto Ready function is activated.  
When the time mode is set to remain time mode,  
these indicators light.  
w RELAY indicator  
Lights when Relay Play mode is activated.  
Total remain mode: Both T and REMAIN indicators  
light.  
e FADE indicator  
Lights when Fade in/out is turned on.  
Track remain mode: REMAIN indicator lights.  
6 Time display  
r MONO indicator  
Lights when in Mono output mode.  
This section is used to show time values, menu  
information or messages.  
t RESUME indicator  
Lights when Resume mode is on.  
y INCR indicator  
Lights when Incremental Play is activated.  
7 Play mode indicators  
u KEY ORIGINAL indicator  
Indicates the current playback mode.  
RANDOM: Random playback mode  
S: Single playback mode  
Lights when Key Original function is turned on.  
PGM: Programmed playback mode  
TASCAM CD-01U/CD-01UPro  
11  
 
4 - Features and their functions  
Rear panel  
1 ANALOG OUTPUT terminals  
5ANALOG OUTPUT (BALANCED) terminals (CD-  
01U Pro only)  
The analog line output terminals are for RCA pin  
jacks. The maximum output level is +6 dBV.  
The analog line output terminals are for XLR  
connectors. The maximum output level is +20 dBu.  
2 DIGITAL (OPTICAL) OUTPUT terminal  
6DIGITAL (AES/EBU) OUTPUT terminal (CD-01U  
Provides the digital audio signal in S/PDIF format.  
This connector outputs the 44.1KHz digital signals  
constantly even if pitch control is activated.  
Pro only)  
Provides the digital audio signal in AES/EBU format.  
This connector outputs the 44.1KHz digital signals  
constantly even if both control is activated.  
3 CONTROL I/O (RS-232C) connector  
This RS-232C interface allows control by a computer  
or by other serial controllers. Consult your TASCAM  
dealer the TASCAM web site for details of this port if  
you wish to use it.  
7CONTROL I/O (PARALLEL) connector (CD-01U  
Pro only)  
Parallel control from an external devices can be  
performed.  
4 RELAY IN/OUT jacks  
8
IN  
These jacks are used to perform the relay play  
operation between two or more CD-01U/CD-01U  
Pro, or perform the fader start or event start  
operation.  
Connect the power cable supplied with the CD-  
01U/CD-01U Pro.  
Remote Control Unit  
1 EJECT BLOCK key  
This turns the Eject Block mode on and off.  
2 DISPLAY key  
Pressing this key changes the time mode on the  
display.  
3 PLAY MODE key  
This selects the playback mode. During selection, the  
playback mode is indicated on the display in the  
following manner.  
Normal playback (in disc order): no indication  
Single playback: S lights up  
Program playback: PGM lights up  
Random playback: RANDOM lights up  
4 EJECT key  
Press this to eject the disc. This key cannot be used  
when Eject Block mode is on and the disc is being  
played back.  
12  
TASCAM CD-01U/CD-01UPro  
 
4 - Features and their functions  
5 PITCH key +/- keys  
o SEARCH keys  
Use these keys to perform the pitch control function.  
During playback or playback standby, press the key  
continuously for review or cue playback (search).  
6 KEY ORIG key  
p INDEX/DIR SEARCH key  
This turns the Key Original function on and off.  
Use this key to select the index (Audio CDs) or  
directory (MP3 discs).  
7 A.CUE/DEL key  
Sets the Auto Cue level.  
During program input, the selected program number  
track is deleted.  
a JOG +/- keys  
Pressing the key in pause mode performs the frame  
accurate search.  
8 A.RDY/INS key  
s¥PLAY key  
Turns the Auto Ready function on and off.  
During program input, inserts a track into the  
program list.  
Press this key to start CD playback.  
When incremental play function is activated, pressing  
this key play start from the next track.  
9 REPEAT key  
dπ READY key  
Turns the Repeat Play mode on and off.  
Pressing and holding this key for one second or  
more enters the Repeat A-B mode.  
When this key is pressed during playback or while  
stopped, enters standby mode.  
0 INTRO CHECK key  
f CALL key  
Enters the Intro Check mode.  
Locates the playback to the last play start point.  
q MENU key  
gª STOP key  
Enters the Menu mode.  
Use this key to stop playback.  
When incremental play function is activated, pressing  
this key pauses at the beginning of the next track.  
w ENTER key  
Confirms the menu options and confirms the settings  
and editing on the menu.  
e PREV key  
Selects the previous menu option or setting on the  
menu.  
r NEXT key  
Selects the next menu option or setting on the menu.  
t Number keys  
These are used to select track numbers.  
y CLEAR key  
During track number input, the track number is  
cleared when this key is pressed.  
u PGM key  
Pressing this key enters the Program mode.  
i SKIP keys  
Use these keys to skip to the previous track or the  
next track.  
TASCAM CD-01U/CD-01UPro  
13  
 
5 - Menu operation  
The various settings and editing operations possible  
with the CD-01U/CD-01U Pro are performed through  
menu options shown on the display. Among the many  
menu setting options, some may be made directly using  
the keys on the remote control.  
No.  
Menu  
Function  
Parameter  
Manual reference  
Page  
Underlined values are fac-  
tory default settings  
01  
02  
03  
KEY-0  
Key Original  
ON, OFF  
Key Original  
21  
23  
19  
19  
21  
22  
21  
BLOCK  
REPEAT  
Eject Block  
ON, OFF  
Eject Block  
Repeat Playback  
A-B Repeat Playback  
Program  
OFF, ON, A-B  
Repeat Playback  
04  
05  
06  
PROG  
FADE  
rogram operation  
OFF, 0.5-10.0  
OFF, ON, FDR  
Program Playback  
Fade In/Out  
Relay Play  
23  
Fade In/Out  
RELAY  
Relay Playback  
Fader/Event Start  
Power on Play  
Mono Output  
Resume  
07  
08  
09  
10  
TIMER  
MONO  
RESUME  
EOM  
ON, OFF  
Power on play  
Output in Mono  
Resume  
20  
20  
18  
23  
ON, OFF  
ON, OFF  
EOM Time  
OFF, 5, 10, 15, 20,  
EOM  
25, 30, 35 sec.  
Incremental Play  
Pitch Step  
11  
12  
13  
14  
15  
INCR  
ON, OFF  
Incremental Play  
Pitch Control  
19  
20  
PITCH  
RS232C  
F-PRE  
U-DATA  
0.1, 0.5, 1.0 %  
96, 192, 384  
(SURE)  
Baud rate setting  
Factory Preset  
User Data  
Restoring the default setting  
24  
ON, OFF  
ÆÆ  
ÆÆ When digital output signal from the AES/EBU terminal is not received correctly on the other digital equipment , set  
the user data to OFF then try again.  
Operation basics  
1 Press the PITCH knob on the front panel when  
SHIFT indicator is lit or press the MENU key on the  
remote control.  
4 Use the PITCH knob on the front panel or  
PREV/NEXT keys on the remote control to select the  
setting value.  
5 Press the PITCH knob on the front panel or ENTER  
Menu No.  
Menu  
Parameter  
key on the remote control.  
Pressing the DISPLAY key on either the front panel or  
the remote control exits the menu mode.  
2 Use the PITCH knob on the front panel, or  
PREV/NEXT keys or number keys on the remote  
control to select the menu item.  
3 Press the PITCH knob on the front panel or ENTER  
key on the remote control.  
14  
TASCAM CD-01U/CD-01U Pro  
 
6 - Playback  
Discs for playback  
The CD-01U/ CD-01U Pro can playback the types of  
discs listed below.  
MP3 files recorded in ISO9660 format on CD-R and  
CD-RW discs, and properly finalized.  
CD-R/RW discs that have not been finalized cannot  
be played back. Make sure the disc has been prop-  
erly finalized before loading into the player.  
Ordinary audio CDs available commercially (recorded  
in CD-DA format).  
CD-R and CD-RW discs recorded in CD-DA format,  
and properly finalized.  
About finalization  
Even if audio data is recorded onto a CD-R/RW disc, if  
the TOC (table of contents corresponding to the record-  
ed data) is not written on the disc after recording, the  
disc cannot be played back on conventional CD play-  
ers. Finalization is the process of writing the TOC on the  
disc.  
copy control CD discs as a means of protecting artist  
copyrights. Some of these discs do not comply with  
standard CD format specifications, and may not be able  
to be played on this unit.  
The CD-01U/CD-01U Pro can play back MP3 files  
recorded in formats which conform to ISO9660 level 1,  
level 2 and Joliet.  
A number of record companies have released titles on  
For MP3 CDs  
CDs containing MP3 files can be played by the CD-  
01U/CD-01U Pro with the following limitations on the  
number of files and directories.  
MP3 files are played as the order in the following diagram.  
In this manner, playback is performed from the top level  
directories.  
Maximum number of directories: 254  
Maximum number of MP3 files: 255  
File format: MPEG 1 audio layer 3  
Bit rate: 32kbps to 320kbps  
Sampling frequency: 44.1KHz, Stereo  
File extension: mp3, Mp3, mP3, MP3  
The CD-01U/CD-01U Pro can only read the files in the  
first session of a multi-session disc.  
ID3 tag display for MP3 playback is not supported.  
: Folder (Directory)  
: MP3 File  
TASCAM CD-01U/CD-01UPro  
15  
 
6 - Playback  
Playback modes  
There are four different playback modes. The mode  
changes the playback mode in the following order:  
selected is indicated on the display.  
Cont Single Program Random  
Normal (continuous) playback mode: no indication lamp  
Single playback mode: S is lit  
You can also select the playback mode pressing the  
CALL/PLAY MODE key on the front panel when in  
SHIFT mode.  
Program playback mode: PGM is lit  
Random playback mode: RANDOM is lit  
While the mode can be changed from any playback  
mode, the explanation in this manual will assume the  
user is starting from the normal Continuous mode.  
The playback mode can be selected using the PLAY  
MODE key on the remote control. Pressing the key  
Basic playback operation  
1 Push the POWER switch to turn on the unit.  
The display will indicate NO DISC.  
back standby mode.  
To resume playback, press the ¥?π key or the front  
panel or ¥key on the remote control.  
2 Insert a disc into the slot, label side upwards.  
After a disc is inserted, the total playing time and  
number of tracks will be displayed.  
To remove the disc  
Press the EJECT key on either the front panel or  
remote control unit.  
Do not force the disc into the slot, the CD-01U/CD-  
01U Pro will pull the disc when partially inserted.  
You can insert back a disc into the slot by pressing the  
EJECT key or pull the disc and slot it in again.  
3 Press the ¥?π key on the front panel or ¥ key on  
the remote control unit.  
The play indication will light up, and playback begins  
from track 1. The number of the current track in play  
is indicated on the display.  
When Eject Block is activated, EJECT key cannot be  
used when disc is being played back.  
To stop playback, press the ª key on the front panel  
or remote control unit.  
To play a desired track  
To pause playback, press the ¥?π key on the front  
panel again or π key on the remote control unit.  
The indication will blink, and the unit will enter play-  
Press the SKIP key to select the desired track or  
numerical keys.  
Using headphones  
Plug the headphone cord into the PHONES jack.  
ume too high. Listening at high volumes for extended  
periods of time may result in permanent hearing dam-  
age.  
Adjust the volume with the volume control.  
When using headphones, take care not to turn the vol-  
Track selection  
Select desired tracks for playback with the skip keys on  
the front panel or on the remote control.  
When Auto Cue is off and the CD-01U/CD-01U Pro is  
in pause mode, the beginning of selected track is locat-  
ed ,and the unit enters playback standby mode.  
To restart playback from the beginning of the track in  
play, press the µ once.  
When Auto Cue is on and the CD-01U/CD-01U Pro is  
in play mode, playback begins after selecting the track.  
To skip to the previous track, press µ twice.  
To skip to the next track, press once.  
When Auto Cue is on and the CD-01U/CD-01U Pro is  
in pause or stop mode, when a track is selected, the  
point where sound begins (not where the track begins)  
on that track is located, and the unit enters playback  
standby mode.  
When Auto Cue is off and the CD-01U/CD-01U Pro is  
in stop or play mode, playback begins after selecting  
the track.  
16  
TASCAM CD-01U/CD-01UPro  
 
6 - Playback  
Selecting by track number  
Frame search  
Using the number keys on the remote control, the num-  
ber of the desired track can be entered directly.  
Even numbers with two (Audio CD) or three (MP3) digits  
can be entered easily.  
During playback standby, using the PITCH knob in shift  
mode performs the frame accurate search.  
Also, during playback standby, pressing the JOG +/-  
keys on the remote control performs the frame search.  
For example:  
Track 9 (Audio CD): press 0 then press 9.  
Track 9 (MP3): press 0, 0, and 9.  
This function does not operate with MP3 discs.  
Search  
During playback or playback standby, pressing the  
SEARCH keys continuously enables the search of a  
desired portion within a track for playback.  
The search function does not operate with MP3 discs.  
TASCAM CD-01U/CD-01UPro  
17  
 
7 - Advanced operations  
Auto Cue  
When the Auto Cue function is turned on and a track is  
selected, the point where sound begins (not where the  
track begins) on that track is located to and the unit  
enters pause mode.  
Turning the Auto Cue function on and off  
Press the µ key on the front panel when SHIFT indi-  
cator is lit or A.CUE/DEL key on the remote control to  
select the auto cue level.  
When the ¥ key is pressed, playback begins at exactly  
that point.  
Auto cue level: OFF (default), -24, -30, -36, -42,  
-48, -54, -60, -66, -72 (dB)  
Auto Cue is not supported for MP3 playback.  
When the Auto Cue function is activated, A.CUE indica-  
tor is lit on the display.  
Even when the power is turned off, the Auto Cue setting  
is maintained.  
During stop mode, to cue to the start of sound on track  
one, just press the π key.  
Auto Ready  
When the Auto Ready function is on, after each track is  
played, playback standby mode is entered at the begin-  
ning of the next track.  
When the Auto Cue function is also on, playback stand-  
by mode is entered at the beginning of the sound on  
the selected track, and not the beginning of that track.  
The behavior of Auto Ready function is follows.  
Continuous play mode:  
Turning the Auto Ready function on and off  
Press the key on the front panel when SHIFT indi-  
cator is lit or A.RDY/INS key on the remote control to  
turn the function on and off.  
Pause the beginning of the next track when playback  
of the current track is finished.  
Single play mode:  
Pause the beginning of the current track when play-  
back of the current track is finished.  
When the Auto Ready function is on, A.RDY indicator is  
lit on the display.  
Program play mode:  
Even when the power is turned off, the Auto Ready set-  
ting is maintained.  
Pause the beginning of the next programmed track  
when playback of the current track is finished.  
Resume  
When the resume function is on, the playback stop  
position is memorized and playback starts from that  
position when playback is resumed.  
number 09 RESUME).  
In the case of MP3 discs, the playback starts from the  
beginning of the last playing track when playback is  
resumed.  
When the Resume function is on, RESUME indicator is  
lit on the display.  
Turning the Resume function on and off  
Even when the power is turned off, this setting is main-  
tained.  
Set the resume function on and off on the menu (menu  
Call  
Pressing the CALL key on either the front panel or  
remote control locates the unit to last play start point,  
and the unit enters playback standby mode.  
This function is not supported for MP3 playback.  
18  
TASCAM CD-01U/CD-01UPro  
 
7 - Advanced operations  
Incremental play  
Turning the Incremental play function on and off  
This function allows auto-cueing of the playback point  
to the start of the next track when the ª key on either  
the front panel or remote control is pressed, or a stop  
command is received from the external device.  
Set the incremental play function on and off on the  
menu (menu number 11 INCR).  
Pressing the ª key again or receiving the stop com-  
mand again, unit enters stop mode.  
When the this function is on, INCR indicator is lit on the  
When this mode is enabled, pressing the ¥ key on the  
remote control or receiving the play command from the  
external device starts playback from the beginning of  
the track following the current track.  
display.  
Even when the power is turned off, this setting is main-  
tained.  
Repeat playback  
Press the REPEAT key on the remote control to turn on  
the repeat mode. In this mode, all the tracks on the disc  
are played continuously.  
enable Program Repeat, Single-track Repeat and  
Random Repeat operations, respectively.  
During playback, if the repeat mode is turned on, play-  
back continues as before, and when the last track fin-  
ishes, playback resumes from the first track. If repeat  
mode is turned on when the deck is stopped, press the  
PLAY key to begin operation.  
Turning the Repeat play function on and off  
Turn the repeat play function on and off on the menu  
(menu number 03 REPEAT). Or press the REPEAT key  
on the remote control.  
When the this function is on, REPEAT indicator is lit on  
the display. Even when the power is turned off, this set-  
ting is maintained.  
Combining the repeat mode with the Program, Single-  
track playback and Random playback functions will  
A to B repeat playback  
If a specific portion between two points on the disc is  
specified, that portion can be played back repeatedly.  
To cancel Repeat A-B mode and resume normal  
playback  
Press the REPEAT key on the remote control once more.  
1 During playback and the repeat function is off, press  
and hold the REPEAT key on the remote control  
more than 1 second. Or set the repeat mode to A-B  
on the menu (menu number 03 REPEAT).  
There are three additional ways to cancel repeat A-B  
mode:  
Press ª key.  
Search the other track.  
Eject the CD.  
REPEAT indicator flashes on the display.  
2 Press the REPEAT key on the remote control or  
PITCH knob on the front panel at the beginning of  
the desired portion on the disc.  
A-B indicator flashes on the display.  
Both repeat start (A) and end (B) points can set to with-  
in a track.  
3 At the end of the desired portion on the disc, press  
the REPEAT key on the remote control or PITCH  
knob on the front panel again.  
REPEAT and A-B indicators are lit up on the display,  
and the desired A-B section will be played repeatedly.  
This function is not supported for MP3 playback.  
TASCAM CD-01U/CD-01UPro  
19  
 
7 - Advanced operations  
Intro Check  
The Intro Check function allows only the beginning of  
each track to be played for 10 seconds.  
This function is operational both at stop and during nor-  
mal playback.  
This function works in normal (continuous) play mode  
and program play mode.  
To exit the intro check mode, press ª key on either the  
front panel or remote control, or INTRO CHECK key on  
the remote control.  
1 Press the STOP/INTRO CHECK key on the front  
panel when SHIFT indicator is lit and playback stops.  
Or, pressing the INTRO CHECK key on the remote  
control to turn the intro check function on and off.  
Int is shown on the display.  
The intro check mode is also canceled when play mode  
is changed.  
2 Press the ¥?π key on the front panel or ¥key on  
the remote control.  
Output in monaural  
Both analog and digital output can be set to mono out-  
When the this function is on, MONO indicator is lit on  
put mode.  
the display.  
Set the mono output mode on and off on the menu  
(menu number 08 MONO).  
Even when the power is turned off, this setting is main-  
tained.  
Power on play  
By using an external timer, you can set the CD-  
01U/CD-01U Pro to play the loaded disc automatically  
when the unit is turned on by the timer.  
4 Set the timer to the desired time.  
Consult the timer's operation manual for details.  
At the set time, the power to the CD-01U/CD-01U Pro  
will be turned on, and playback will automatically begin.  
1 First, plug the power cord of the CD-01U/CD-01U  
Pro into the power outlet of the timer.  
2 Load a CD into the unit.  
3 Set the TIMER menu (menu number 07 TIMER) to on.  
Pitch control  
When playing back an audio CD or MP3, the pitch (or  
speed) of the playback can be varied.  
Pitch can be varied +/- 12.5%.  
value is shown on the display and PITCH indicator  
lights.  
2 Rotate the PITCH knob or use the PITCH +/- keys to  
set the pitch.  
Use the PITCH menu (menu number 12 PITCH) to  
adjust the pitch control steps from 0.1, 0.5, or 1.0%  
(Default: 0.1%).  
1 Press the PITCH knob on the front panel when  
SHIFT indicator is unlit or press the PITCH key on  
the remote control to turn the Pitch Control function  
on and off.  
Digital output provides the 44.1KHz digital signals con-  
stantly even if pitch control is activated.  
When the pitch control function is activated, pitch  
20  
TASCAM CD-01U/CD-01UPro  
 
7 - Advanced operations  
Changing the palyback speed without changing the key (Key Original)  
When the Key Original function is ON, you can change  
the playback speed without changing the key.  
When the Key Original function is ON, you may find that  
the audio has artifacts not present when just Pitch is  
used. This is an expected result of the Key Original pro-  
cessing, it does not indicate a problem with the unit.  
Turn the Key Original function on and off on the menu  
(menu number 01 KEY-O). Or pressing the KEY ORIG  
key on the remote control turns this function on and off.  
Use the PITCH knob on the front panel when SHIFT  
indicator is unlit, or use the PITCH and PITCH +/- keys  
to change the playback speed without affecting the key.  
Program playback  
This function enables playback of selected tracks in any  
desired order. Up to 100 tracks can be selected from a  
CD for Program playbacK.  
3 Press the SEARCH ˚ key. The track number will be  
entered into the program.  
Or turning the PITCH knob right enters the selected  
track number into the program.  
1 During stop mode, press the PGM key on the remote  
control.  
4 Repeat the above step 2 and 3 until the desired  
program is completed.  
Track No.  
Program No.  
5 When program is completed, press the PITCH knob  
on the front panel or PGM key on the remote control.  
Even when the power is turned off, program is main-  
tained.  
Or enter the program menu (menu number 4 ProG)  
then press the PITCH knob.  
When the disc is ejected, the program lists are erased.  
2 Use the number keys or SKIP keys on the remote  
control, or SKIP keys on the front panel to select  
each desired track for program playback.  
Editing a programmed track  
1 Enter the program mode.  
3 Use the number keys or SKIP keys on the remote  
control or SKIP keys on the front panel to edit the  
programmed track.  
2 Use the SEARCH keys to select the track for editing.  
Also using the PITCH knob on the front panel to  
select the track for editing.  
4 When editing is completed, press the PITCH knob on  
The track number will be shown in the display.  
the front panel or PGM key on the remote control.  
Adding a track to the program  
1 Enter the program mode.  
4 Use the number keys or SKIP keys on the remote  
control or SKIP keys on the front panel to input the  
track number of the track to be added.  
2 Use the SEARCH keys on the front panel or remote  
control, or using the PITCH knob on the front panel  
to select the programmed track before the portion  
you wish to add a track.  
5 Press the PITCH knob on the front panel or PGM key  
on the remote control to exit the program mode.  
The track number should be shown in the display.  
3 Pressing the DISPLAY key and SEARCH ˚ key  
simultaneously on the front panel or pressing the  
A.RDY/INS key adds the program step.  
TASCAM CD-01U/CD-01UPro  
21  
 
7 - Advanced operations  
Deleting a programmed track  
1 Enter the program mode.  
3 Pressing the DISPLAY key and SEARCH key  
simultaneously on the front panel or pressing the  
A.CUE/DEL key deletes the selected track.  
2 Use the SEARCH keys to select the track for deletion.  
Also using the PITCH knob on the front panel to  
select the track for deletion. The track number will be  
shown in the display.  
4 Pressing the PITCH knob on the front panel or PGM  
key on the remote control exits the program mode.  
Fade-in and fade-out  
When this function is on and CD playback begins, the  
song fades in. When playback is finished, the song  
fades out.  
3 Set the Fade in time using with the PITCH knob on  
the front panel or PREV/NEXT keys on the remote  
control.  
4 Press the PITCH knob on the front panel or ENTER  
key on the remote control to set the fade in time and  
enter the fade out time setting.  
The length of the fade in/out to/from the normal level  
can be set between 0.5 and 10 seconds in 0.5 second  
increments (Default setting: OFF).  
1 To set the fade operation, enter the fade menu (menu  
number 05 FADE).  
5 Set the Fade out time using with the PITCH knob on  
the front panel or PREV/NEXT keys on the remote  
control.  
6 Press the PITCH knob on the front panel or ENTER  
key on the remote control to set the fade out time  
and exit the menu.  
2 Press the PITCH knob on the front panel or ENTER  
key on the remote control to enter the fade in time  
setting.  
Relay Play  
When the disc in the first unit in a chain plays to the  
end, the disc in the next unit in the chain will start.  
4. To activate the relay play function, set the relay play  
menu (menu number 06 RELAY) to on for all the units  
in the chain.  
Make all connections with power off.  
RELAY IN  
RELAY OUT  
1. Check to see that all the CD-01Us are turned off.  
RELAY IN  
2. Refer to the diagrams, and connect the first CD-  
01U's RELAY OUT to the second CD-01U's RELAY  
IN, the second CD-01U's RELAY OUT to the third  
CD-01U's RELAY IN, and so on. Finally, connect the  
last CD-01U's RELAY OUT to the first CD-01U's  
RELAY IN.  
RELAY OUT  
RELAY OUT  
RELAY IN  
3. Switch on power to all the CD-01Us.  
RELAY OUT  
RELAY IN  
RELAY IN  
22  
TASCAM CD-01U/CD-01UPro  
 
7 - Advanced operations  
Time display switching  
During audio CD playback (or playback standby), when  
the DISPLAY key on either the front panel or the  
remote control is pressed, the time display will switch  
through several modes in the following order.  
When playing an MP3 disc, elapsed track time is always  
displayed, and the DISPLAY key does not operate.  
Even when the power is turned off, the time display  
mode setting is retained.  
Elapsed track time (no display light indication)  
Remaining track time (REMAIN is lit in the display)  
Remaining disc time (T. and REMAIN are lit in the display)  
When in program play mode, remaining total program  
time (when T.REMAIN is lit) and total program time  
(when stopped) are shown.  
When stopped, the total recording time is shown, regard-  
less of the status of the TOTAL and REMAIN indicators.  
End of track warning (EOM)  
When nearing the end of a track, a warning indication is  
shown on the display.  
To set the warning display time, use the EOM menu  
(menu number 10 EOM).  
The number of seconds before the track end that the  
warning is displayed can be set beforehand, so that  
when playback reaches that point, the two colons will  
begin flashing on the display.  
EOM time can be set from OFF, 5, 10, 15, 20, 25, 30  
(default), and 35.  
This function is not supported for MP3 playback.  
Eject block  
When eject block is on, the EJECT key cannot be used  
when a disc is being played back or paused.  
Use the eject block menu (menu number 02 BLOCK) to  
turn this function on and off.  
Fader start/Event start  
Fader start/stop  
Connect the RELAY IN jack (mini jack) on the rear panel  
and fader start terminal on the external device which  
supports the fader start function.  
For CD-01U Pro only, connect the CONTROL I/O  
(PRALLEL) terminal on the rear panel and fader start  
terminal on the external device.  
SLEEVE  
STOP  
CONTROL I/O  
RELAY IN  
STOP  
PIN8 GND  
START  
START  
PIN11  
FADER STRAT/STOP  
TIP  
SLEEVE  
TIP  
The relay play menu (menu number 06 RELAY) should  
be set to FDR.  
See more detailes for the CONTROL I/O terminal in the  
secsion External parallel control on page 24.  
TASCAM CD-01U/CD-01UPro  
23  
 
7 - Advanced operations  
Event start  
The relay play menu (menu number 06 RELAY) should  
be set to ON.  
Connect the RELAY IN jack (mini jack) on the rear panel  
and event start terminal on the external device which  
supports the event start function.  
Restoring factory default settings  
To restore all settings to their factory defaults:  
The following settings are restored to default values.  
1 Select the factory preset menu (menu number 14 F-  
PRE).  
Playback mode  
Time display mode  
Auto ready  
2 The display shows 14 flashing, then press the PITCH  
knob on the front panel or ENTER key on the remote  
control to confirm the selection.  
Auto cue  
Pitch control value  
All menu settings  
3 The display shows - SURE - flashing to recomfirm  
that this operation is surely desired.  
You can cancel to restore the default settings either the  
stage 14 F-PRE or SURE is flashing by pressing the  
other keys except the SHIFT key and the PITCH knob  
on the front panel.  
4 Press the PITCH knob on the front panel or ENTER  
key on the remote control to restore all settings to  
their default values.  
External parallel control  
The CD-01U Pro can be controlled from an external  
devices which supports a parallel interface via the CON-  
TROL I/O terminal on the rear panel.  
Pin No. Description  
In/Out  
Out  
In  
1
2
3
4
5
6
7
8
9
Stop tally  
Skip (Back)  
Skip (Forward)  
No Disc tally  
EOM tally  
Search (Back)  
Search (Forward)  
GND  
In  
Out  
Out  
In  
REMOTE(PARALLEL)  
In  
1
8
Play tally  
Out  
Out  
In  
10 Pause tally  
11 Fader start/stop  
12 Stop  
15  
9
In  
13 Play  
In  
14 Pause  
In  
15 +5V  
In:  
Input signals are active when low (ground) for > 30 ms.  
Out:  
Tally signals are open collector, with a maximum current of 50 mA.  
+5V:  
The maximum current supplied from this terminal is 50 mA.  
24  
TASCAM CD-01U/CD-01UPro  
 
8 - Specifications  
Specifications  
Type  
Compact Disc player  
Discs  
8 or 12cm (3.1 to 4.7inch) CD, CD-R/CD-RW  
Formats  
Audio CD (CD-DA), MP3  
2-channel  
Number of channels  
Resolution  
16-bit  
Sampling frequency  
Analog line outputs  
Connectors  
44.1kHz  
RCA  
Maximum Output level  
Output impedance  
Analog line outputs (CD-01U PRO only)  
Connectors  
+6 dBV dBu  
1kØ  
XLR-3-32 (1:GND, 2:HOT, 3:COLD)  
Maximum Output level  
Output impedance  
Headphones  
+20 dBu  
150Ø  
Connectors  
standard stereo jack  
20 mW + 20 mW  
32Ø  
Maximum Output level  
Load impedance  
Digital input (Coaxial)  
Connectors  
Optical  
Format  
IEC60958-3 (S/PDIF)  
Digital output (AES/EBU, CD-01U PRO only)  
Connector  
XLR-3-32  
Format  
IEC60958-4 (AES/EBU)  
Frequency response  
S/N ratio  
20Hz to 20kHz +0.5/- 1.0dB  
> 95dB (20kHz LPF A-WTD)  
> 98dB (20kHz LPF A-WTD)  
< 0.01% (200Hz HPF, 20kHz LPF)  
> 90 dB (at 1 kHz)  
Dynamic range  
Total harmonic distortion  
Channel separation  
Wow and flutter  
Voltage requirements  
Below measurable limits (less than 0.001%)  
USA/CANADA  
U.K./Europe  
120 CVAC, 60 Hz  
230 VAC,50HZ  
240 VAC,50Hz  
Australia  
Power consumption  
Dimensions  
9 W (CD-01U)  
11 W (CD-01U PRO)  
482.6 x 50 x 333.9 mm  
19 x 2 x 13.1 (in)  
Weight  
3.5 kg (7.7 lbs)(CD-01U)  
3.7 kg (8.1 lbs)(CD-01U Pro)  
5 to 40 degrees C (41F to 104F)  
Operating temperature range  
For product improvememt, specifications and external  
appearance are subject to change without notice.  
Due to product improvement, the actual unit may  
appear differently than illustrations in the operation  
manual.  
TASCAM CD-01U/CD-01UPro  
25  
 
8 - Specifications  
Dimensional drawing  
435mm (17.1")  
482.6mm (19")  
Error messages  
Err 01 TOC Read error - the disc's Table of Contents cannot be read - try with another disc or remove and clean the  
existing disc before replacing it  
Err 02 GFS error GFS signal cannot be detected - try with another disc or remove and clean the existing disc  
before replacing it  
Err 03 Focus error - after repeating the attempt eight times to focus, an error still occurs - try with another disc or  
remove and clean the existing disc before replacing it  
Err 04 Sub-Q error - the sub-Q code cannot be detected - try with another disc  
Err 05 Loading error - the loading operation cannot be completed, even after retries, or there is an internal error - make sure  
that there are no obstructions preventing the loading operation  
Err 06 Sled error - an internal drive error - try turning the power off, waiting a few seconds, and turning it on again  
Err 07 S-DRAM error - an internal S-DRAM error - try turning the power off, waiting a few seconds, and turning it on again  
Err 08 System error - an internal error - try turning the power off, waiting a few seconds, and turning it on again  
If any of the numbered error messages occur, try using another disc.  
If the errors continue with a number of discs, turn the unit off, wait for a few seconds, and turn it on again.  
If the errors still continue or other error occurs, contact your TASCAM distributor for repair.  
26  
TASCAM CD-01U/CD-01UPro  
 
CD-01U/CD-01UPro  
27  
 
»
CD-01U /CD-01UPro  
TEAC CORPORATION  
Phone: +81-422-52-5082  
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan  
TEAC AMERICA, INC.  
Phone: +1-323-726-0303  
7733 Telegraph Road, Montebello, California 90640  
TEAC CANADA LTD.  
Phone: +1905-890-8008 Facsimile: +1905-890-9888  
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada  
TEAC MEXICO, S.A. De C.V  
Phone: +52-555-581-5500  
Campesinos No. 184, Colonia Granjes Esmeralda, Delegaacion Iztapalapa CP 09810, Mexico DF  
TEAC UK LIMITED  
Phone: +44-1923-438880  
5 Marlin House, Croxley Business Park, Watford, Hertfordshire. WD1 8TE, U.K.  
TEAC EUROPE GmbH  
Phone: +49-611-71580  
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany  
TEAC ITALIANA S.p.A.  
Phone: +39-02-66010500  
Via C. Cantu 11, 20092 Cinisello Balsamo, Milano, Italy  
Printed in China  
 

Team Products Drill CM9130 User Manual
Topfield DVR TF 5000 User Manual
Toshiba Air Conditioner MMY MAP0804HT8 E User Manual
Toshiba Camcorder B10 User Manual
Toshiba Flat Panel Television 20DL74 User Manual
Toshiba Projection Television 62HM15 User Manual
Uniden Cordless Telephone CLX475 User Manual
Univex Lawn Mower 385002X108 User Manual
Vivitar Digital Camera VT027 RED User Manual
Vizio Work Light E390 A1 User Manual